StudentShare
Contact Us
Sign In / Sign Up for FREE
Search
Go to advanced search...
Free

The Properties and Features of the Wood Material - Lab Report Example

Cite this document
Summary
The paper "The Properties and Features of the Wood Material" highlights that experiment generally dwelled on the main objective of providing a better understanding of the properties and features of the wood material. The experiment was done using four primary samples…
Download full paper File format: .doc, available for editing
GRAB THE BEST PAPER97.1% of users find it useful
The Properties and Features of the Wood Material
Read Text Preview

Extract of sample "The Properties and Features of the Wood Material"

Timber Test Lab Report al Affiliation The lab report generally comprises of an experimental set up that was aimedtowards determining various wood tests. This set-up was generally aimed towards enabling for computation of the maximum compression strength as well as the ultimate modulus of elasticity. The basic consideration was that; they all set basis on both parallel and perpendicularly aligned set-ups. The experimental procedure also enabled for identification of the general influence of both the wood type, failure mechanism, as well as the wood direction. The main factors under study in this lab test were on the aspects of the static bending as well as the ultimate compression of the given wood. The primary focus for undertaking this lab experiment was the fact that it is very essential to be conversant with various wood properties since it is a very vital construction element. On the other hand, wood is regarded as an anisotropic component. It is due to the fact that; its features tends to vary with respect to the wood’s grain structure. It hence necessitates for the utilization of various elastic constants. The variation often occurs on the basis of Radial, Longitudinal, as well as the Tangential faces as shown below: Introduction: Objectives The main objective of undertaking this lab experiment was to assist in providing a better understanding of the properties and features of the wood material. To ascertain with this ultimate aim, the experiment was done using four primary samples. It was based on the fact that; two of these samples were used for testing the compressive strength in such a manner that the load was aligned in a parallel position. The other two were also subsequently performed in such a manner that the load was aligned in a perpendicular position to the grains. This set-up was generally meant for enabling for computation of the maximum compression strength as well as the ultimate modulus of elasticity. The basic consideration was that; they all set basis on both parallel and perpendicularly aligned set-ups. The experimental procedure also enabled for identification of the general influence of both the wood type, failure mechanism, as well as the wood direction (New York Lumber Trade Association, 1923). Experimental Procedure: Static Bending A. Tangential In this segment, the lab experiment started by first taking the measurements of the width, Length, as well as the height of the beam specimen. After recording these dimensions, the beam’s mid-point was then marked alongside the member’s length. After it, the specimen was the mounted on the testing apparatus while ensuring that the bearing block is centered at the specimen’s midspan. Using the testing machine’s slow range’s slow speed, the entire beam was then loaded. The levels of deflections were then recorded accordingly after the proportion of about 100 pounds load. The beam was then loaded to the failure until its visibility is observed. All the results were then clearly recorded before analyzing them. B. Radial: The experimental procedure for this set-up resembled the one for the tangential set-up. The only difference emerged when it came to the aspect of computing and making the final analysis with regards to the results. Compression: A. Longitudinal (Stresses parallel to the grains) Here, the initial procedure was the act of measuring both the length as well as the cross-sectional area of the given test material. While doing this, it was placed in an upright position within the test machine. The specimen was then loaded with the testing machines cross head of about 0.005”/min until it reached the failure mode. The records were then made after a constant proportion of 1000 pounds load. The machine’s speed was the increased up to 0.2”/min, all the way from 0.1”/min. This was specifically done after the failure so as to bring out a clear and distinct view with regards to the failure mode. The results were then recorded accordingly before plotting a stress verses strain curve. B. Radial and Tangential (Stresses perpendicular to the grains) The widths and the bases of the specimen were initially measured accordingly. This was then followed by the act of computing the loading area through multiplication of both variables. The steel block was then used to apply the given load. This was entirely done until the indicator reached an ultimate point of around 0.1” with regards to the change in length. This hence enabled for determination of the loading area. The stress verses strain curve was the plotted as in part A. Results: Static Bending: Radial Length (wood) Height (h) Width (b) Length (arm) Length (Upper arm) Weight (lbs.) 17.875 1.44 1.43 16.625 5.625 0.578 Tangential Length (wood) Height (h) Width (b) Length (arm) Length (upper arm) Weight (lbs.) 17.75 1.47 1.45 16.625 5.625   Radial Load (lbs.) Deflection (Δx) Tangential Load (lbs.) Deflection (Δx) 100 0.028 100 0.046 200 0.054 200 0.064 300 0.105 300 0.081 400 0.129 400 0.099 500 0.154 500 0.117 600 0.181 600 0.134 700 0.208 700 0.152 800 0.237 800 0.17 900 0.27 900 0.193 1000 0.305 1000 0.211 1100 0.345 1100 0.235 Failure* 1235 0.365 1200 0.257 1300 0.284 1400 0.322 Failure* 1456 0.36 Graphical Presentation: Compression: Longitudinal Length (wood) Height (h) Width (b) Length (arm) Length Weight (lbs.) 2.921 1.416 1.451 16.625 5.625 0.096 Radial Length (wood) Height (h) Width (b) Length (arm) Length Weight (lbs.) 2.9 1.41 1.448 16.625 5.625 0.096 Radial Load (lbs.) Deflection (Δx) Longitudinal Load (lbs.) Deflection (Δx) 1000 0.011 2000 0.023 2000 0.03 3000 0.027 2700 0.115 4000 0.031 2800 0.167 5000 0.035 2900 0.217 6000 0.041 3000 0.251 7000 0.046 Failure* 3114 0.291 8000 0.051 9000 0.058 10000 0.074 Failure* 11185 0.08 Graphical Presentation: Longitudinal Radial: Discussion: The results obtained above brought in a clear view with regards to the wood properties. For instance, the ultimate wood property can be entirely determined through the computation of the Modulus of Rapture (MOR), as well as the Flexural Modulus of Elasticity (MOE) (American Society of Civil Engineers & United States, 1942). From the above results; MOR for the Radial= Mc/I M= 1235 C= 0. 365 I = (1.43×1.4/12 = 0.7276 Therefore; MOR = (1235 × 0.365)/ 0.7276 = 619.54 MOR for the Radial = (1456 × 0.36)/ 0.807 = 649.52 The results also show that; the amount of the exerted load is directly proportional to deflection. On the other hand, the results also indicated that there is a mutual correlation between the stress and strain. This was clearly shown in the two graphs above that are characterized with a curve that tends to increase gradually with increase in the stress levels. The results also confirmed that wood is actually much stronger towards its longitudinal direction. The longitudinal direction’s tensile strength tends to be larger as compared to the compressive strength when they act towards the same direction. In addition, it was realized that the longitudinal tensile strength is almost 40 times greater than the acting tensile strengths in either the tangential or radial directions (American Society of Civil Engineers & United States, 1942). Finally, it was noticed that the longitudinal compressive strength is often six times greater in either longitudinal or radial directions. Conclusion: The lab experiment generally dwelled on the main objective of providing a better understanding on the properties and features of the wood material. To ascertain with this ultimate aim, the experiment was done using four primary samples. It was based on the fact that; two of these samples were used for testing the compressive strength in such a manner that the load was aligned in a parallel position. The other two were also subsequently performed in such a manner that the load was aligned in a perpendicular position to the grains. Finally, the experimental procedure enabled for identification of the general influence of both the wood type, failure mechanism, as well as the wood direction. References: American Society of Civil Engineers., & United States. (1942). Timber test study: A work projects administration project. San Francisco, California. New York Lumber Trade Association. (1923). Report of Timber Test Committee. New York: Lumber Trade Association. Read More
Cite this document
  • APA
  • MLA
  • CHICAGO
(Engineering Materials lab- Timber Test Lab Report Example | Topics and Well Written Essays - 1750 words, n.d.)
Engineering Materials lab- Timber Test Lab Report Example | Topics and Well Written Essays - 1750 words. https://studentshare.org/engineering-and-construction/1880124-engineering-materials-lab-timber-test-lab
(Engineering Materials Lab- Timber Test Lab Report Example | Topics and Well Written Essays - 1750 Words)
Engineering Materials Lab- Timber Test Lab Report Example | Topics and Well Written Essays - 1750 Words. https://studentshare.org/engineering-and-construction/1880124-engineering-materials-lab-timber-test-lab.
“Engineering Materials Lab- Timber Test Lab Report Example | Topics and Well Written Essays - 1750 Words”. https://studentshare.org/engineering-and-construction/1880124-engineering-materials-lab-timber-test-lab.
  • Cited: 0 times

CHECK THESE SAMPLES OF The Properties and Features of the Wood Material

Solar Energy Harnessing

It is to be noted that the energy band gap theory suggests that transparency of a material is closely related to the electrical behavior of a material, more specifically its resistivity.... Transparency of a material is higher if the band gap between the valence and conduction band is high.... To achieve this, doping is done in selected semiconductors, which can modify their properties to give us transparent layers with high conduction (Nave, 20102)....
6 Pages (1500 words) Dissertation

Movie Review Guidelines:

Addicted to Plastic Reflection: This video explains the significance of plastic as a material and its usability.... Plastic is a very popular material and is used for making almost everything.... 6 May, Addicted to Plastic Reflection: This video explains the significance of plastic as a material and its usability.... Plastic is a very popular material and is used for making almost everything.... Plastic is a material that retains its quality and properties over time and can be recycled and reused infinitely....
2 Pages (500 words) Assignment

The Stress-Strain Curve of Polymers under the Effect of Tensile Loading

hellip; Introduction The method of tensile testing involves testing a material specimen for failure by the application of a tensile force.... ‘Stress-strain curves are an extremely important graphical measure of a material's mechanical properties' (Roylance, 2001).... The stress-strain curve for the specimen is an important method of characterizing the behavior of the material and adjudging its suitability as a material for any function....
4 Pages (1000 words) Essay

Principles of Aesthetic Value

In analyzing clay roof tiles using formal properties and cultural perspectives, it is possible to make ordinary roofing materials into pieces of art which can evoke senses of beauty and history, among other things.... Using the properties of unity and organization, clay roof tiles can be seen in another light by evoking onlookers a sense of unity and organization with regards to the arrangement of the tiles on the roof, as well as being properly-arranged, with no misplaced tile in sight....
6 Pages (1500 words) Essay

Maintenance of Sterility

Specifications define the various properties and characteristics of the sterile barrier system, establishing limits where appropriate.... Some properties that may be included in a specification are dimensional requirements, seal strength, and seal integrity to name a few....
7 Pages (1750 words) Essay

Physical and Chemical Properties of Methylene Chloride

This essay "Physical and Chemical properties of Methylene Chloride" focuses on the methylene chloride, also known as dichloromethane (DCM) is an organic compound with the chemical formula CH2CL2.... It is a colourless, volatile liquid with a characteristic sweet aroma.... nbsp;It is soluble in methanol, diethyl ether, n-octanol, and acetone, partially soluble in water....
3 Pages (750 words) Essay

Hazardous Properties of Chemical Substances

he first property is that polymeric materials are stiff because they are constituted of very high mechanical features to their density.... The paper "Hazardous properties of Chemical Substances" highlights that Trinitrotoluene melts at a temperature of (80 °C or 176 °F), which is far much lower than its explosion point....
1 Pages (250 words) Essay
sponsored ads
We use cookies to create the best experience for you. Keep on browsing if you are OK with that, or find out how to manage cookies.
Contact Us