StudentShare
Contact Us
Sign In / Sign Up for FREE
Search
Go to advanced search...
Free

Stress strain experiment - Lab Report Example

Cite this document
Summary
Strain is the ratio of increase in length to original length when an object is subjected to some force (stress). It is made of a small diameter wire or an etched metal foil that…
Download full paper File format: .doc, available for editing
GRAB THE BEST PAPER94% of users find it useful
Stress strain experiment
Read Text Preview

Extract of sample "Stress strain experiment"

College Strain gauge A strain gauge as the suggests is an electrical device used to measure the strain of an object. Strain is the ratio of increase in length to original length when an object is subjected to some force (stress). It is made of a small diameter wire or an etched metal foil that is attached to a backing material. The wire is coiled severally to create a long wire. The principle of operation is based on electrical resistivity of the wire. The electrical resistance R of a wire of length L with cross-sectional area A can be illustrated by the formulae; Where is the strain.

From the above equation we can draw an inference that the electrical resistance of the wire changes with strain:i. As strain increases, the wire length L increases, which increases R.ii. As strain increases, the wire cross-sectional area A decreases, which increases R.For most materials, as strain increases, the wire resistivity also increases.When the stain gauge is subjected to some stress the wire properties do change and hence gives us a measure of strain.The strain gauge is put into practical application in measuring the stain in bridges, structural beams, and weigh bridges and in motor vehicle industries.

Stain gaged is mounted on the structural beams and used to measure the shrinkage on subject to some force.Relatively it is difficult to measure the real change in resistance of the strain gauge and the change need to be converted into an electrical signal. To obtain a real result, the strain gauge is connected to an electric circuit which is commonly a Wheatstone bridge to give a real measure of strain electrically. The Wheatstone bridge measures small change in resistance and outputs it as a voltage.

Graph of stress against strain when a wire of area 122.65625mm2, initial length of 50 mm and diameter is 12.5 mmFrom the graph we can analyse that mild steel is stronger than aluminium metal. On observing the yield strength points, mild steel has it at 350N/mm2 and for aluminium is at 200 N/mm2. Young’s modulus E is found by calculating the slope of the elastic region of the curve (which is point from origin to the point of yield stress.) For mild steel; =1250For aluminium; E=2346Graph of stress against strain when a wire of area 19.

625mm2, initial length of 50 mm and diameter is 5 mm.In conclusion from the young’s modulus results we can conclude that aluminium is more stiff than mild steel.ReferencesYang, B. (2005). Stress, strain, and structural dynamics an interactive handbook of formulas, solutions, and MATLAB toolboxes. Amsterdam: Elsevier Academic Press.

Read More
Cite this document
  • APA
  • MLA
  • CHICAGO
(“Stress strain experiment Lab Report Example | Topics and Well Written Essays - 500 words”, n.d.)
Retrieved from https://studentshare.org/engineering-and-construction/1629347-stress-strain-experiment
(Stress Strain Experiment Lab Report Example | Topics and Well Written Essays - 500 Words)
https://studentshare.org/engineering-and-construction/1629347-stress-strain-experiment.
“Stress Strain Experiment Lab Report Example | Topics and Well Written Essays - 500 Words”, n.d. https://studentshare.org/engineering-and-construction/1629347-stress-strain-experiment.
  • Cited: 0 times

CHECK THESE SAMPLES OF Stress strain experiment

Internal Pressure

Finally, we will project the outcome of the experiment on the cylinder as the pressure increases to some unknown large finite threshold.... As stresses are very hard if not impossible to measure, we will use strain gauges to determine the respective strains on the cylinder and then translate these results into their corresponding stresses from ideal thin cylinder theory. … We will also compare theoretical projections to experimental results, measuring how far off from the ideal a real cylinder approximating the condition of "thinness" is....
4 Pages (1000 words) Lab Report

Measuring Forces in Truss Members

This is done theoretically to determine causes of failure in the pin connections and theoretically calculating the yield that… Also, the critically buckling load for the trusses is calculated theoretically. The laboratory project's main objective was to become familiar with the operation and application of electrical resistance wire strain gages to measure stresses in simple structures and to experimentally determine the internal forces in simple structures, and to compare those results with values obtained analytically....
9 Pages (2250 words) Lab Report

Determination of principle stress

This experiment focused on using Mohr's strain circle to determine the principle directions, principle strains, and maximum strain.... The masses were used to record the gauge strain readings at different loading levels.... From the given experimental readings the Mohr's circle was drawn and the principle strain, principal direction, and maximum strain determined.... This way, the normal stress on each of the plane differs from one… However, in one plane, normal stress value may be of a maximum value....
5 Pages (1250 words) Lab Report

Stress and Strain of Aluminum

The report "Stress and strain of Aluminum" focuses on the laboratory analysis of the stress and strain of the structure of aluminum molecules.... nbsp;From the graph, the stress of a material decreases gradually with an increase in strain, this means the material becomes nonlinear as stress is increased.... As strain is increased, atoms move to new positions to create a new equilibrium in the material.... A fracture may be experienced if a strain continues beyond the proportionate limit....
5 Pages (1250 words) Lab Report

Measuring Forces in Truss Members Using Strain Gages

High levels of accuracy were found for this experiment.... The paper "Measuring Forces in Truss Members Using strain Gages" states that the analytical determination of forces in truss members using the method of joints holds true in that experimental results.... Engineers can also determine the actual forces acting through structural members using strain gauges, which give the actual magnitude and direction of forces through structural members....
12 Pages (3000 words) Lab Report

Determination of the Tensile Strength of Metals

t is paramount to wear safety glasses before beginning the experiment since broken pieces of metals can cause harm to your eyes.... Additionally, gloves help protect the person conducting the experiment from any residue on the machine and samples.... The paper "Determination of the Tensile Strength of Metals" states that different metals have their tensile strengths varying according to the amount of load they can effectively support per unit area....
8 Pages (2000 words) Lab Report

Strain Gauge: Measurement and Instrumentation

In this study, a stain gauge was attached to… The objective of the experiment involves using the bending beam and the circuit bridge in the calibration of the strain gauge.... The objective of the experiment involves using the bending beam and the circuit bridge in the calibration of the strain gauge.... Diagram 1: Apparatus Procedure The experiment was set up as shown is in diagram 2.... The objectives that were set for this experiment were realized....
2 Pages (500 words) Lab Report

Engineering Mechanics Experiments - Deflection of a Simply Supported Beam

This experiment was successful in showing the actual deflections in a beam which differed by up to 0.... This experiment shall investigate the forces acting on an overhanging beam with double load acting upon it.... imThe main aim of this experiment was to investigate Shear force variation for various loading conditions.... ethodFigure 4: Setup for shear force experiment (single point load)Set the test apparatus to zero in readiness for applying the load....
14 Pages (3500 words) Research Paper
sponsored ads
We use cookies to create the best experience for you. Keep on browsing if you are OK with that, or find out how to manage cookies.
Contact Us